LCOM1920-T5G03

#ifndef UART_H_INCLUDED

#define UART_H_INCLUDED

/**

 * @defgroup uart uart

 * @ingroup libs

 * @brief UART module.

 *

 * @{

 */

/// @brief COM1 base address

#define COM1_ADDR           0x3F8

/// @brief COM2 base address

#define COM2_ADDR           0x2F8

/// @brief COM1 IRQ line

#define COM1_IRQ            4

/// @brief COM2 IRQ line

#define COM2_IRQ            3

/// @brief COM1 Vector (???)

#define COM1_VECTOR         0x0C

/// @brief COM2 Vector (???)

#define COM2_VECTOR         0x0B

/**

 * @brief Possible parity schemes for UART.

 */

typedef enum {

    uart_parity_none = 0x0,

    uart_parity_odd  = 0x1,

    uart_parity_even = 0x3,

    uart_parity_par1 = 0x5,

    uart_parity_par0 = 0x7

} uart_parity;

/**

 * @brief UART configuration

 */

typedef struct {

    /// @brief  Base address of the serial port this configuration was read from

    int     base_addr               ;

    /// @brief  LCR (Line Control Register)

    uint8_t lcr                     ;

    /// @brief DLL (Divisor Latch Least significant byte)

    uint8_t dll                     ;

    /// @brief DLL (Divisor Latch Most significant byte)

    uint8_t dlm                     ;

    /// @brief Number of bits per char

    uint8_t bits_per_char           ;

    /// @brief Number of stop bits

    uint8_t stop_bits               ;

    /// @brief Parity scheme

    uart_parity parity              ;

    /// @brief Break control (???)

    uint8_t break_control         :1;

    /// @brief Divisor Latch Access Bit (1 if DLL, DLM can be accessed)

    uint8_t dlab                  :1;

    ///  @brief Divisor latch

    uint16_t divisor_latch          ;

    /// @brief IER (Interrupt Enable Register)

    uint8_t ier                     ;

    /// @brief  Receiver data interrupt enabled if 1

    uint8_t received_data_int     :1;

    /// @brief  Transmitter empty interrupt enabled if 1

    uint8_t transmitter_empty_int :1;

    /// @brief  Receiver line status register (LSR) change interrupt enabled if 1

    uint8_t receiver_line_stat_int:1;

    /// @brief  Modem status interrupt enabled if 1

    uint8_t modem_stat_int        :1;

} uart_config;

/**

 * @brief Subscribes UART interrupts and disables Minix Default IH.

 * @param interrupt_bit Bit of interrupt vector that will be set when UART interrupt is pending

 * @param interrupt_id UART interrupt ID to specify the UART interrupt in other calls

 * @return ERROR_CODE code representing the result of the operation, SUCCESS code is returned if everything is OK

 * @see {_ERRORS_H_::errors}

 */

int (subscribe_uart_interrupt)(uint8_t interrupt_bit, int *interrupt_id);

/**

 * @brief Get UART configuration.

 * @param   base_addr   Base address of the serial port whose configuration we want

 * @param   config      Pointer to uart_config where the read configuration will be stored

 * @return SUCCESS if operation is successful, other value otherwise

 */

int uart_get_config(int base_addr, uart_config *config);

/**

 * @brief Print to stdout a UART configuration in a human-friendly way.

 * @param   config  UART configuration to be printed

 */

void uart_print_config(uart_config config);

/**

 * @brief Set number of bits per character.

 *

 * Valid numbers of bits per char go from 5 to 8.

 * @param   base_addr       Base address of serial port

 * @param   bits_per_char   Number of bits per char

 * @return                  SUCCESS if operation is successful, other value otherwise

 */

int uart_set_bits_per_character(int base_addr, uint8_t     bits_per_char);

/**

 * @brief Set number of stop bits.

 *

 * Valid numbers of stop bits are 1 and 2.

 * @param   base_addr   Base address of serial port

 * @param   stop        Number of stop bits

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_set_stop_bits         (int base_addr, uint8_t     stop         );

/**

 * @brief Set parity scheme to be used.

 * @param   base_addr   Base address of serial port

 * @param   par         Parity scheme

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_set_parity            (int base_addr, uart_parity par          );

/**

 * @brief Set bit rate.

 *

 * Valid numbers of bit rates go up to 115200 bps.

 * @param   base_addr       Base address of serial port

 * @param   bit_rate        Number of bits per second

 * @return                  SUCCESS if operation is successful, other value otherwise

 */

int uart_set_bit_rate          (int base_addr, uint32_t    bit_rate     );

/**

 * @brief Enable Receiver Register Ready interrupts

 * @param   base_addr   Base address of serial port

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_enable_int_rx (int base_addr);

/**

 * @brief Disable Receiver Register Ready interrupts

 * @param   base_addr   Base address of serial port

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_disable_int_rx(int base_addr);

/**

 * @brief Enable Transmitter Register Empty interrupts

 * @param   base_addr   Base address of serial port

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_enable_int_tx (int base_addr);

/**

 * @brief Disable Transmitter Register Empty interrupts

 * @param   base_addr   Base address of serial port

 * @return              SUCCESS if operation is successful, other value otherwise

 */

int uart_disable_int_tx(int base_addr);

/**

 * @}

 */

/**

* @defgroup nctp    nctp

* @ingroup uart

* @brief NCTP (Non-Critical Transfer Protocol) module.

* @{

*/

/**

 * @brief Initialize NCTP structures.

 * @return SUCCESS if operation is successful, other value otherwise

 */

int nctp_init(void);

/**

 * @brief Dump all the content of the NCTP in/out queues.

 * @return SUCCESS if operation is successful, other value otherwise

 */

int nctp_dump(void);

/**

 * @brief Set function to be called when a full message is received.

 * @return SUCCESS if operation is successful, other value otherwise

 */

int nctp_set_processor(void (*proc_func)(const uint8_t*, const size_t));

/**

 * @brief Free resources taken on NCTP initialization.

 * @return SUCCESS if operation is successful, other value otherwise

 */

int nctp_free(void);

/**

 * @brief Send a message throught serial port COM1

 * @param   num     Number of different blocks to send in the message

 * @param   ptr     Array of length num, with pointers to blocks that should be sent

 * @param   sz      Size of each block that should be sent, in bytes

 * @return SUCCESS if operation is successful, other value otherwise

 */

int nctp_send(size_t num, const uint8_t *const *ptr, const size_t *const sz);

/**

 * @brief Get NCTP interrupt handler error code.

 * @return  SUCCESS if previous interrupt handler call was successful, other value otherwise

 */

int (nctp_get_ih_error)(void);

/**

 * @brief NCTP interrupt handler.

 *

 * @note Must be called on all interrupt cycles. Even if not necessary, it must be

 * called so the NCTP is allowed to dump any messages it might receive, even

 * if those messages are unexpected.

 */

void nctp_ih(void);

/**

 * @}

 */

#endif //UART_H_INCLUDED